I have made 3 scenes: Armed away, Armed Home and Disarmed. They all work flawlessly and change the arming mode in Smartthings.

I have seen that there is a tile that, when pressed, contains the same functions.

My problem is I can't get this tile to change state.

What am I doing wrong or is this tile not working?

Anyway for you to add a sticky note tile in the future?

The generic icons cannot cover all uses, so how can I use my own images for tile icons? For example, there are no icons for water pump, water heater, or boiler (to name a few). I have media tile images for these, but how do I use them for the device icons?  

This morning, several of my tiles were grey with small "?" in the middle.  Have not seen this before.  Nothing changed in the last few weeks.  When I touched some of the tiles, they resumed working, but some are still showing grey with "?".  Getting same behavior on both my Samsung Tab A and my iPad.

Hi, I have in mind to manage two hubs, a Smartthings and a Hubitat, I want to know if in a single panel it is possible to insert devices managed by different hubs and to do this I need to have some special care. Thank you

I have seen a lot of questions related to the Ring Doorbell and Kindle Fire...I figured out a workable solution:

Sideload the Google Play Store onto the Fire (I used the instructions at https://www.howtogeek.com/232726/how-to-install-the-google-play-store-on-your-amazon-fire-tablet/ )

Use the Play Store to install the Ring Doorbell app

Use the Play Store to install AutomateIt

Setup 2 rules in AutomateIt:

Rule 1:  On notification from Ring, run the Ring App

Rule 2:  On notification from Ring, run the Fully App with a 1 minute delay

AutomateIt will notify you that it needs permission to monitor notifications.  Allow that permission.

Start Fully, ring your doorbell, see your front porch, cheer, wait another half minute or so, and Fully restarts, conduct victory lap...and profit.

If you have motion detection turned on for the doorbell, this will also show your porch if something trips the motion sensor.

Hi, I would like to know if it is possible to link ActionTiles to Alexa. I would like to find an alternative to the SmartThing hub and thought I could use the Amazon hub. Thank you

Currently the new feature allows for just one pin code. Adding more pin codes will allow the user to assign codes to different members of the family or temp codes to guests without needing to share their own code. Individual PINs would need to be revocable.

I'm sharing this for others to use!

Use this Media Still Image URL:

https://sunsettile.app/sunset?lat=38.7535121&long=-120.5807933&bgcolor=3b3749&fgcolor=ffffff&size=3x2

Use the base URL https://sunsettile.app/sunset for sunset and https://sunsettile.app/sunrise for sunrise

Required parameters: 

lat (latitude)

long (longitude)

bgcolor (background color  - hex color without #)

fgcolor (foreground color - hex color without #)

Optional parameters:

timeformat=24 (For 24 hour time)

offset= (number of minutes, positive or negative)

Please set the refresh time to at least every 12 hours (43200 seconds) to be nice to my server.

Currently, I can see the air quality CO2, PM2.5, PM10, AQI, Temp, and Humidity in Hubitat tiles, but in ActionTiles, I cannot access PM2.5, PM10 and AQI.  Any idea how I can get these attributes from Hubitat over to ActionTiles?

Suddenly I'm not authorized to see my panel or chose hubs to connect to on my laptop but everything is working fine on ios and android.. tried restarting the browser and logging off from actiontiles application with no luck.. any idea??

With the death of Simple Device Viewer, I no longer have an easy way to know what devices are offline. SmartThings will spam me forever about batteries being below 15%, but it never seems to tell me when devices are offline (other than when the hub goes offline).

Is it possible to display the offline status of devices in ActionTiles? Preferably as a third option (for a contact sensor this would be open, closed, offline), but I'll take whatever will work.

It's possible that the API that SDV relied on is the same one that ActionTiles relies on, in which case I could see this would not be possible.

Thanks.

I'm sorry if this is a newby question this is my first time using ActionTiles. All I want to do is show this website on one of my tiles. And for some reason it says the URL is not valid. Could you please tell me what I am doing wrong. Thank you.

I decompiled Ring's android apk and found this this activity (launched in landscape) which appears relevant to pulling up the app to get a live view:

<activity android:name="com.ringapp.ui.activities.LiveViewLoadingActivity" android:screenOrientation="landscape" android:theme="@android:style/Theme.NoTitleBar.Fullscreen"/>

How does one craft the url schema to call this activity? e.g.

com.ringapp/com.ringapp.ui.activities.LiveViewLoadingActivity

Could anybody do a quick comparison between ActionTiles and the recently released Google Home Hub?  Thanks in advanced.

I've added a Z-Wave Smoke Alarm to Smartthings. The icon shows a smoke alarm on the ST app, which is great. On the AT maintenance panel, it shows a smoking cigarette, which is fine, but the panel display only shows a question mark. 

Is there currently a way that I can make the Panel Background transparent?  I have tried to add a comma after the last RGB number and in the preview it shows as transparent, but that actual panel does not when loaded.